Skip to content

Cart

Your cart is empty

PAPIER INSTALLATION GUIDE

Please click here to view PDF.

IMPORTANT: PLEASE READ BEFORE INSTALLING

ONCE YOUR INSTALLATION IS COMPLETE, PLEASE SEND IT TO US DEARS; WE’LL TAG YOU AND SHARE IT FOR OTHER DANDIES TO ENJOY!

1. The supplier shall provide a complete copy of Fine & Dandy Co.’s current Hanging Instructions to the installer pertaining  to the installation of the wallcovering. ALL INSTALLATIONS MUST CONFORM TO FINE & DANDY CO.’S CURRENT INSTALLATION INSTRUCTIONS AND PRODUCT TECHNICAL INFORMATION. If the wallcovering is installed in a manner other  than that recommended by Fine & Dandy Co., it is done at the sole risk of the installer. Use of a mold inhibiting primer  product and the use of an adhesive containing a mildew inhibitor is recommended. 

2. All labels shall be checked for accuracy by the installer to ensure that the shipment is received as ordered. 

3. If no defect is evident before installation, THE MATERIAL SHOULD BE INSPECTED AFTER THREE (3) PANELS ARE INSTALLED. IF ANY DEFECT AT THIS TIME OR ANY POINT OF THE INSTALLATION NO FURTHER MATERIAL SHOULD BE APPLIED AND FINE & DANDY CO. SHOULD BE CONTACTED IMMEDIATELY. FINE & DANDY CO. WILL NOT BE LIABLE FOR  CHARGES OVER THREE PANELS OF MATERIAL. 

HANGING ORIENTATION:

The preferred orientation for most random patterns is reverse hanging of alternating panels. However, for some items such  as metallic prints or special directional embossings like grasscloth or glass beads, installations may benefit from straight  hanging of these products. This is due to the high reflectivity of some print finishes and embossings and the variation these  products have under different lighting conditions. If there is any doubt about the optimum hanging orientation of a given  product, installers should review both methods on 3 strips to determine the optimum performance before proceeding to  the full installation. 

SURFACE PREPARATION:

A. For best hanging results, the drywall surface should be finished to a level 4 prior to installation. 

B. All hanging surfaces must be clean, smooth, dry, undamaged, free of mold, mildew, grease or stains, and structurally  intact. All loose paint and other wallcoverings should be removed. If moisture is present, immediately identify and eliminate  the source(s) of the moisture and verify that all wall surfaces are completely dry before proceeding. 

C. Any mold or mildew MUST be removed from walls and hanging surfaces prior to installation. Walls should not contain in  excess of 4% residual moisture content. A moisture meter should be used to determine moisture content. Moisture infiltration  and accumulation can lead to mold or mildew growth and must be corrected PRIOR to the installation of the wallcovering.  If you are unsure if moisture problems are present, consult a qualified professional before proceeding. This product is intended for use in buildings that are properly designed and maintained to avoid moisture infiltration, condensation and  or accumulation at wall cavities and wall surfaces, particularly in warm, humid climates. Walls should also be treated with  bleach, Lysol and/ or other approved, mildew–inhibiting products in order to inhibit further mildew growth. Fine & Dandy  Co. will not be responsible for any performance and/or quality issues if moisture problems are not addressed before installation,  and/or if the building is not properly maintained to prevent moisture infiltration following installation. 

D. Proper surface preparation is key to getting great results. To prepare the surface properly, we recommend that you prime  all surfaces with a universal, white-pigmented, mold inhibiting wallcovering primer. For example we recommend ZINSSER®  Shieldz® Universal Wallcovering Primer. 

E. Use only a lead pencil for marking walls and back of wallcovering. Do not use a ballpoint or marking pen, they will bleed  through the surface. 

F. Do not install wallcovering unless a temperature above 65 degrees F is maintained in both areas of installation and storage  for at least 48 hours prior to installation. 

ADHESIVE APPLICATION:

Hang wallcovering with a premium quality heavy-duty clear or clay pre-mixed adhesive. Use of a mildew inhibitor in the  adhesive is recommended as above instructions. Roman Adhesives Eco Brand Primer and Adhesives are recommended to  comply with NSF-342 Sustainability Do not dilute adhesive. Brush an even coat of paste over the entire back of the wallcovering. Pay particular attention to run over edges so they are sure to be pasted. Book material for ten minutes. 

SELECTING AND CUTTING WALLCOVERING: 

A. Before cutting, examine goods to make certain pattern colour is satisfactory and as ordered. 

B. Cut rolls in sequential order starting with the highest number working down to the lowest number. Make certain that run  numbers are broken at the corners only. Allow for matching of repeats and trimming at ceilings and baseboards. 

C. Number panels and headers as they are cut from the roll and apply to the wall in the same sequence.

APPLYING WALLCOVERING TO WALL SURFACE:

1. Determine whether the pattern match is random, straight across, or drop match. Measure the wall height, allowing for  pattern match, add 4 inches, and then cut the wallcovering. It will overlap onto the ceiling and the base approximately 2  inches. 

2. Apply the recommended adhesive to the back using either a pasting machine or a paint roller. Work the adhesive in, to  cover the back completely, especially near the edges. Fold each end toward the middle, pasted sides together, aligning the  edges carefully so they do not dry out. CAUTION: DO NOT CREASE WALLCOVERING. Allow to “relax” for ten minutes  (booking). This will allow the adhesive to penetrate the wallcovering fabric, which is important to a successful installation. 

3. WITH ALL DIRECTIONAL PATTERNS, IT IS IMPORTANT TO LINE UP PATTERNS AT EYE LEVEL ALLOWING ANY DRIFT  IN LINEUP TO RUN OFF TOWARD CEILING AND FLOOR. THE STANDARD ALLOWANCE IS ONE QUARTER OF AN INCH  UP OR DOWN. IF PATTERN IS LINED UP AT THE CEILING THE PATTERN WILL BEGIN MISALIGNMENT SOONER AND  THE GAP WILL BE LARGER. ALSO, MOST PATTERNS WILL BE VIEWED AT EYE LEVEL THEREFORE IT IS THAT AREA THAT  NEEDS TO LOOK ALIGNED. IF THERE ARE ANY QUESTIONS ABOUT PATTERN LINEUP, CONTACT US. BE SURE FIRST  DROP OF WALLCOVERING IS SQUARE ON WALL BY PLUMBING THE WALL AND USING A LEVEL. 

4. Goods are designed to match up to 53” wide on walls depending on the pattern. WHEN INSTALLING, EXACT TRIMMING  AND LINE UP OF THE PATTERN IS CRITICAL (See installation instructions specified to each design.)

5. AVOID BURNISHING THE FACE OF THE MATERIAL. WALLCOVERINGS SHOULD BE INSTALLED ONLY WITH THE  FELT LINED SQUEEGEE PROVIDED IN YOUR ORDER BY FINE & DANDY CO INC. 

6. Do not rub. Do not allow vinyl adhesive to dry on the surface as it may leave a white residue. Wash off excess paste from  the face of the wallcovering as you hang it with a cellulose sponge. The cellulose sponge must be rinsed in clean water after  every use. Blot dry with a clean cloth. 

7. Overlap the second strip over the edge of the first strip. Tape seams underneath with a low adhesive tape before overlapping  and double cutting to avoid getting adhesive on the wallcovering. TO LESSEN SEAM ISSUES, DOUBLE CUT THE WALLCOVERING  WITHOUT CUTTING INTO THE WALL OR SHEETROCK BY USING A SPECIAL SEAM CUTTING KNIFE (FOR EXAMPLE,  USE ADVANCE QUALITY PRODUCTS “SEAM BUSTER WALLPAPER KNIFE”). A new blade must be used for each cut for best results. Use a soft bristle brush to wash the ceiling and the baseboard to remove any paste residue. Do not leave any  overlap on the seams since vinyl will not adhere to itself. *Seams should be vertical, have a tight fit, and be free from air  and paste bubbles. Seams should not be located closer than 6" to corners. 

For wallcoverings that DO NOT have a white background colour, we recommend that once the panels are applied to the walls, but beforethe seams are closed and glued down, the edge of each panel should be “chalked” using a hard pastel that is matched as closely to the  background colour of the wallcovering as possible so that the seams are not white or visible. A damp microfibre cloth can be used to wipe away any excess pastel. 

8. After installation, the walls and wallcovering should be monitored for potential moisture or vapour infiltration or accumulation.  Any such infiltration/accumulation after installation must be promptly eliminated in order to reduce the risk of mold/mildew growth. 

CARE AND MAINTENANCE OF WALLCOVERING:

I. General Conditions Day-to-Day Soil

Ordinary dirt and smudges can be removed with a mild soap and warm water. Clean from bottom of wall upward. Rinse  thoroughly with clean water from the top down using a sponge. Dry wallcovering with a soft lint free cloth or towel.  

DO NOT use steel wool or powdered abrasive because they mark the surface leaving an unsightly appearance. DO NOT use active solvent type cleaning preparations, such as nail polish remover, etc...because they remove the print, and/or finish from the wallcovering. 

Care should be taken that water dripping down the wall does not run behind the floor molding. The molding can be discoloured and/or permanently damaged.  All stains should be attempted to be removed with soap and water only.  

QUESTIONS?

contactus@fineanddandycompany.com
fineanddandycompany.com
@fineanddandyco